Installing a Electronic Boost Controller - Am I on the right track?

Corrupt

Leaving Skid Marks
Lifetime Member
Location
Western Australia
First Name
Nick
Drive
Daily: 1998 Galant VR-4
Project: 1934 Ford Roadster
Title says it all really.

Scored a BLITZ EBC Type R as a garage clean-out gift/freebie for helping a bud of mine.

As well as that, over the Christmas break i FINALLY bought the last gauge i needed to start/finish my install (DEFI Boost/Water Temp/Oil Temp).

Yes the gauges are DEFI's. Yes its a bit lux. Yes its taken me almost 5 years to get all 3 gauges (THAT MATCH) and the control unit.

Long story short, while the VR-4 is off the road and the engine is out i want to get all the hardware, electrics and the Gauge Pod trimmed and installed and set up so the tuner just has to go from the OEM Boost Solenoid to the BLITZ one, within reason.

Following this as a basis:

EBC-installation.jpg


And trying to make heads and tails of the manual for the BLITZ EBC with a translation app in hand, i came to this:

BLITZ.png


Seeing as i haven't dabbled with boost related installs since my 180/S13 days (almost 20 years ago *COUGH* *COUGH*) am i on the right track?

From memory, I'm thinking the boost gauge just tee's into the same line as the controller?

Also i know i'm missing the 2nd line from the intake elbow, wondering if it tee's into the "IN" line to the EBC Solenoid Valve.

Please feel free to correct me/the image as its been a while, maybe some extra brain power will finish it off.

Before some says "Just buy "X" controller", a free controller, my time and spending that extra money on a tune is a better deal for me.

****************** EDITIED 24/01/2026 : UPDATED IMAGE FOR FUTURE REFERENCE BASED ON COMMENTS RECIEVED, IGNORE ABOVE *****************

BLITZ.png
 
Last edited:
Title says it all really.

Scored a BLITZ EBC Type R as a garage clean-out gift/freebie for helping a bud of mine.

As well as that, over the Christmas break i FINALLY bought the last gauge i needed to start/finish my install (DEFI Boost/Water Temp/Oil Temp).

Yes the gauges are DEFI's. Yes its a bit lux. Yes its taken me almost 5 years to get all 3 gauges (THAT MATCH) and the control unit.

Long story short, while the VR-4 is off the road and the engine is out i want to get all the hardware, electrics and the Gauge Pod trimmed and installed and set up so the tuner just has to go from the OEM Boost Solenoid to the BLITZ one, within reason.

Following this as a basis:



And trying to make heads and tails of the manual for the BLITZ EBC with a translation app in hand, i came to this:



Seeing as i haven't dabbled with boost related installs since my 180/S13 days (almost 20 years ago *COUGH* *COUGH*) am i on the right track?

From memory, I'm thinking the boost gauge just tee's into the same line as the controller?

Also i know i'm missing the 2nd line from the intake elbow, wondering if it tee's into the "IN" line to the EBC Solenoid Valve.

Please feel free to correct me/the image as its been a while, maybe some extra brain power will finish it off.

Before some says "Just buy "X" controller", a free controller, my time and spending that extra money on a tune is a better deal for me.

Just buy a….

🤣


Looks like your top image is correct. The Blitz is simply showing that the solenoid sits between the boost signal and wastegates. Our boost signal is off the throttle body elbow, and the T the turbos is a hard line buried like a nightmare.
 
As above. Take the boost reference from the factory location on the throttle elbow as the turbo compressor housings have no provisions to take a ref from.
Make sure NOT to reuse the red tipped factory boost ref hose as that length of hose has a steel restrictor pill in it.


Before some says "Just buy "X" controller", a free controller, my time and spending that extra money on a tune is a better deal for me.
On this subject, if your paying someone to reflash your ecu, your better off selling the EBC and buying a 3 port mac valve and getting the boost tuned via the stock ecu. Itll give you a better result
 
Thanks for the tips.

Ok, i think its sorta coming back to me...

BLITZ.png
Tee off between plenum and fuel solenoid to CPU (Sample Air into CPU)
CPU talks to solenoid brick about sample air and changing it (...0011...100011...111100...01111...)
Tee of both turbo wastegates to IN on solenoid brick (Boost Air out)
Solenoid brick changes the air and OUT goes back to the throttle body elbow (New boost air out)
Boost gauge (and sensor, forgot to show it) tees off between new solenoid brick and throttle body elbow (HowMuchNewBoostAirOutIsThereNow PSI)

?

Just wanted to make sure i got the "suck and blow" directions correct. Also if i don't draw it out and question it i won't understand it.

On this subject, if your paying someone to reflash your ecu, your better off selling the EBC and buying a 3 port mac valve and getting the boost tuned via the stock ecu. Itll give you a better result

It must be my Scottish heritage coming out, but "free is free".

If i was to sell the EBC i'd have to deal with Marketplace (yuck) and to be honest, if i didn't get a free one i probably wouldn't be trying it, i'd just stick the gauges in and say "look what i can see". As for tuning, a tweak or reflash, i might as well drive a Ferrari cos that what they'll charge here anyway...

I had plans of chasing performance, but times and circumstances change... 27 year old me would have agreed about getting a better result, but 37 year old me? Better result or a good result, it's a result, that's all i'm interested in.

If it straight up doesn't work, well...
images.jpg
 
Tee off between plenum and fuel solenoid to CPU (Sample Air into CPU)
Yes
Tee of both turbo wastegates to IN on solenoid brick (Boost Air out)
Incorrect, wastegate T is solenoid OUT.
Solenoid brick changes the air and OUT goes back to the throttle body elbow (New boost air out)
Incorrect. Throttlebody elbow (before the throttle plate) is your boost source, this will go to solenoid IN (without limiting pill)
Boost gauge (and sensor, forgot to show it) tees off between new solenoid brick and throttle body elbow (HowMuchNewBoostAirOutIsThereNow PSI)

Incorrect, boost gauge signal line off intake manifold plenum after the throttle plate.



For what it is worth, I had a Greddy Profec-B on my white car (PFL) in the mid 00s while living in Japan. Was fun but still limited by the stock boost cut.

I installed a manual controller a few months ago, and it was real fun but real unsteady/spiked all over. It lasted three days in the car.

Installed a MAC 3-port (Grimmspeed EBCS I had lying around) and haven’t looked back. But that is a rabbit hole since it takes tuning to work properly and there is cost involved.

So, just remember how our cars work with boost, it’s not as simple as just turning up the pressure. More info here: https://www.ozvr4.com/threads/car-s...brief-second-around-3000rpm.17569/post-360812
 
Last edited:
Yes
Incorrect, wastegate T is solenoid OUT.
Incorrect. Throttlebody elbow (before the throttle plate) is your boost source, this will go to solenoid IN (without limiting pill)
Incorrect, boost gauge signal line off intake manifold plenum after the throttle plate.
Ah i see what i did, got my lines crossed over the new solenoid. This is the direction i was looking for, thanks Abe.

I'll make some tweaks to the image, at least it'll help someone else in the future who may be unsure/unclear as i was.

The last 3 points make sense to me:
Greddy - Worked even with limitations
Manual - Fun but unreliable
3-Port - Cheap but can become a heap of time/money (that personally, i have neither)
 
Attached a new sketch from comments recieved, should be ok now.

Thanks again!
 
Top Bottom