My Evo Bonnet

Discussion in 'Customising Your VR-4' started by Guest, Nov 17, 2007.

  1. Guest

    Guest Unregistered

    just test fitted it, fits perfectlty...
    gonna organise a paint job for it soon-ish

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
  2. leebutts

    leebutts 1 AYC Bar

    Joined:
    Jul 15, 2007
    Messages:
    3,290
    Likes Received:
    43
    Location:
    New Zealand
    First Name:
    Lee
    Drive:
    2001 Golf GTI
    Mate, that is gonna look wicked - where did you get it from and how much?

    cheers

    Lee
     
  3. Guest

    Guest Unregistered

    well its originally from

    www.speedfactory.co.nz

    its normally $750nz

    i bought it from a guy that changed his mind/needed the cash

    for $520nz picked it up last night
     
  4. snickells

    snickells Leaving Skid Marks Lifetime Member

    Joined:
    Jul 13, 2007
    Messages:
    2,899
    Likes Received:
    19
    Location:
    Australia
    First Name:
    Anon
    Drive:
    Car
    Are you going to match the body colour or contrast it or something?
     
  5. Guest

    Guest Unregistered

    match it to the car...

    im not into the different coloured bonnet look...

    looks cheap and as if you couldnt afford a paint job...

    ive taken it back off the car for that reason :D
     
  6. naughtika

    naughtika OzVR4 Stalker Moderator Trader

    Joined:
    Jul 13, 2007
    Messages:
    9,482
    Likes Received:
    518
    Location:
    Brisbane, QLD
    First Name:
    Christian
    Drive:
    '96 Galant VR4, '17 MB A180, '25 Macan GTS
    just a Q about the vent.. are you worried about water getting inside the engine bay?
     
  7. Guest

    Guest Unregistered

    it can have water sheild fitted underneath if need be.
     
  8. naughtika

    naughtika OzVR4 Stalker Moderator Trader

    Joined:
    Jul 13, 2007
    Messages:
    9,482
    Likes Received:
    518
    Location:
    Brisbane, QLD
    First Name:
    Christian
    Drive:
    '96 Galant VR4, '17 MB A180, '25 Macan GTS
    ones from evo will work fine i assume.. :D
     
  9. Fred

    Fred Leaving Skid Marks

    Joined:
    Nov 5, 2007
    Messages:
    311
    Likes Received:
    3
    Location:
    Orange N.S.W 2800
    First Name:
    Fred
    Drive:
    1998 Legnum VR-4 & 1999 Legnum VR-4 w. Recaros
    looks the part...
     
  10. snickells

    snickells Leaving Skid Marks Lifetime Member

    Joined:
    Jul 13, 2007
    Messages:
    2,899
    Likes Received:
    19
    Location:
    Australia
    First Name:
    Anon
    Drive:
    Car
    Ace man, I cant wait to see how it looks all finished then.
     
  11. SiliconAngel

    SiliconAngel 1 AYC Bar

    Joined:
    Aug 7, 2007
    Messages:
    5,213
    Likes Received:
    77
    Location:
    Perth, WA
    First Name:
    SA, Trevor
    Drive:
    '99 Legnum VR4 Black MT
    Looks fantastic Carsten! Nice work, especially for the price!! :D
     
  12. SLY-031

    SLY-031 Leaving Skid Marks

    Joined:
    Oct 2, 2007
    Messages:
    1,391
    Likes Received:
    21
    Location:
    South Australia
    First Name:
    Joel
    Drive:
    VR-4 Legnum
    What sort of water shield are you referring to? Any ideas what a freight company would charge to send something over to to Aus?
     
  13. Guest

    Guest Unregistered

    SLY-031 -> it would be riculously cheaper to pick up the evo 6 main vent and side air duct (ive got one of those sitting here anyway) and glass it on, im sure if it was a weight thing a full fibreglass mold could be taken and reproduced as is currently being down with the evo 3 kit that ive made for my mirage/2door lancer.

    the entire process would cost more but if there was a bodykit company that wished to do the mold for you, it would end up a lot cheaper and they can resell more of them
     
  14. Guest

    Guest Unregistered

    Hey, was it just a straight fit or was there some modifying that was needed to get it on
     
  15. Guest

    Guest Unregistered

    not just weight (my fibreglass one feels 2-3kg lighter at least).... unless you get a good panel shop to do it, its quite easy to spot that its just been slaped on there, and $$ wise prob a shit load more expensive get vents put on the factory bonnet, and time consuming,


    shit loads, prob cheaper by slow boat, i would imagine upto $200 for shipping of a bonnet


    it is a bonnet specifically made for the legnum/galant and is 100% bolt on
    bolts to the factory hinges and has a bonnet catch already attached...

    all it needs is some paint and some heat sheilding.



    .
     
  16. Guest

    Guest Unregistered

    carsten your the man....hehe...

    thats a nice one u got over there....

    post the picture when u got it painted....
     
  17. Guest

    Guest Unregistered

    looking good.
     
  18. leebutts

    leebutts 1 AYC Bar

    Joined:
    Jul 15, 2007
    Messages:
    3,290
    Likes Received:
    43
    Location:
    New Zealand
    First Name:
    Lee
    Drive:
    2001 Golf GTI
  19. Guest

    Guest Unregistered

    ive seen that sytle in RL, its evo 7-ish

    it comes with sheilds and bonnet catch

    its moulded of a prefacelift bonnet, so is very flat,

    and the vent looks all wrong, very cheap and ugly IMO...
    the clear coat goes yellow after a while aswell,

    heres RL pic's

    these flatter it... in person looks like cheap shit.

    [​IMG]

    [​IMG]


    mind you a good CF evo bonnet is around $1200nz (i would fork out for the quality item rather than buy the cheap ebay one you have there)





    .
     
  20. leebutts

    leebutts 1 AYC Bar

    Joined:
    Jul 15, 2007
    Messages:
    3,290
    Likes Received:
    43
    Location:
    New Zealand
    First Name:
    Lee
    Drive:
    2001 Golf GTI
    cheers for the warning Gly!

    Lee
     

Share This Page