Part numbers to be added to Parts Guide

[Guest]

Yeah that's the genuine part mate, chuck it in Ebay or Google and get a picture and see if it's what your after and what else it fits in.

 

[Guest]

Rocker Cover Gaskets, Have seen a few people ask and it doesn't seem to be on the list
http://mitsubishi.epc-data.com/legnum/ec5w/lygf/engine/rocker-cover/401,376,382,390,398,403/

MD 174560

 

[VOLK]

Fieldy started a new thread about it, since it wasn't in here...

Hey Fellas,
I want to change my lifters and while I'm at it replace all the seals for injectors, spark plugs, bolts etc. The reason I want to change everything as I have oil in my spark plug tubes and can hear a vac leak coming from my front fuel rail, plus my lifters tick quite a bit.

So here is a list seals, gaskets, O rings etc that can be changed during a lifter change. Down a little further is a list of other parts/tools/supplies that might be needed/helpful when it comes to doing the job.

Here is my parts list:
MD614805 x 6 - Injector seals
MD087060 x 6 - Injector seals
1465A188 x 6 - Injector seals
MD095402 x 1 - fuel rail to manifold spacer (incase I lose any)
MB554317 x 3 - fuel line o ring
MD614756 x 1 - fuel regulator o ring
MD174560 x 2 - rocker cover gasket
MD347006 x 1 - Intake manifold gasket
MD184662 x 1 - throttle body gasket (check part number as not all VR4s have the same)
MD327253 x 18 - bolt seals
MD178940 x 6 - spark plug tube seals
Lifters x 24
Spark Plugs x 6

Optional Parts

MD183547 x 1 - PCV Valve, some people change this, some dont bother
1057A033 x 1 PCV Valve gasket
MD197340 x ? - Bracket that holds spark plug leads together, in case any break

Other Supplies
Conduit in various sizes to replace all the factory conduit that would of fallen to peices.
Electrical Tape
Gasket Sealant - Threebond SS1 (part#SS1-85-BP available from Bursons) for rocker covers
Lifter Tool
Nickel Anti-seize
dielectric grease - cleaning coil packs

If you have any money left after getting all that, I recommend a carton of beer. A few to drink while working and the rest to celebrate getting the job done or to give to your helper.

And for anyone wanting any idea of what it cost to change all these parts, I think I have found the cheapest suppliers for everything and its going to cost about $500 for the main parts and I guess it will end up around $600 once I get all the other little supplies required.


I started a new thread as I thought it may be useful to others wanting to do this, as most of these parts are not found in the parts guide.

 

[veegeeta]

Caps @ end of cams (seal bung) mitsubishi number MD180402 These are 4 black cap seals

 

[naughtika]

Caps @ end of cams (seal bung) mitsubishi number MD180402 These are 4 black cap seals

added

 

[Guest]

Hey guys am I blind but I don't know if there's a front wheel bearing in this list? I want font and rears, I know the eclipse for rear but does front apply too?, sorry if I'm not ment to post here

 

[veegeeta]

Front hub carrier bearing from bearing supplier koyo dacf1092a.

Hey guys am I blind but I don't know if there's a front wheel bearing in this list? I want font and rears, I know the eclipse for rear but does front apply too?, sorry if I'm not ment to post here

 

[Leg]

looking for part numbers for FL brake pads, can find numbers anywhre

 

[godzilla]

FL and Pre are same same

Go to first page for part numbers

 

[Dice]

Part number for the Tridon thermostat looks wrong, it should be TT281-180. The one listed is about 2mm smaller at the foot/base.

 

[Guest]

If that's the case, is there is a 72c option still?

 

[Dice]

No but there is a 77c option: TT281-170

 

[Dr_Josh001]

MD183547 VALVE,PCV
1057A033 GASKET,PCV VALVE

Aftermarket from Repco etc:

Valve: PCV-038
Grommet/Gasket: PCG-03

 

[mills_88]

Can anyone give me a hand and find the part number for the front inner universal joint assembly please. Left and right would be handy.

 

[rockit]

32043L MR336596 JOINT KIT,FR AXLE SHAFT,LH TJ
32043R MR336597 JOINT KIT,FR AXLE SHAFT,RH TJ

that's what the ASA gave me says it applies to all EC5A and EC5W.

 

[mills_88]

That'll be the one, TJ would stand for tripod joint which is what it is. Cheers mate.

 

[gorgath]

I may be wrong on this one but I've just noticed that this thread is not sticky?

 

[Macca]

I may be wrong on this one but I've just noticed that this thread is not sticky?

It is now

 

[Dice]

No but there is a 77c option: TT281-170

I can now confirm this part fits, it is installed and working fine in my Legnum. The factory equivalent (82C thermostat) is Tridon TT281-180.

 

[The Borg]

I just got all my engine mounts off Mitsubishi Aus and had them installed, they mentioned they can order them in with a 3 week waiting period as there hasn't a big demand for them but in saying that if the demand was to increase they were thinking of having them as a regular shelf part as they are steadily getting demand for grey evo parts. Anyway part numbers are:
Bracket-Engine front mount: MI-MR198377 Cost $314.67
Bracket-T/M Mounting: MI-MR198557 Cost $221.49 ( I have a manual )
Bracket-Roll stopper: MI-MR198381 Cost $102.11
Bracket-Engine RR roll stopper: MI-MR131864 Cost $81.43